What we supply

Industrial valves

Valves are chosen by line parameters, not by appearance: body material, leakage class, actuator and documents.

Request a valve selection All capabilities

We supply pipeline valves and their spare parts to the parameters of the process line. Required documents and tests are included in the agreed order scope — we do not claim checks that are not carried out.

What it solves

The valve was chosen by DN alone and does not hold the medium or temperature.
The replacement does not fit the face-to-face length of the line.
The actuator does not match in torque, power supply or mounting.
It is unclear which form of conformity assessment applies to the item.

What we supply

Wedge and knife gate valves
Wafer and gear-operated butterfly valves
Full and reduced bore ball valves
Check, control and safety valves
Electric and pneumatic actuators, valve trim

Input data we work with

Valve type and connection
DN and PN or pressure class
Process medium and temperature range
Body material and sealing requirements
Operation: manual, gearbox, actuator

How selection works

We match medium, temperature and pressure against the body and seat materials.
We verify face-to-face length, connection type and the mating flanges.
We calculate the required torque and choose manual or actuated operation.
We confirm the leakage class and the fail position on loss of power.

Matching sheet

Parameter	Original	Proposed	Assessment
Type	Butterfly valve	Butterfly valve	match
DN / PN	DN 150 / PN 16	DN 150 / PN 16	match
Body	ductile iron	ductile iron	match
Disc	stainless steel	stainless steel	match
Liner	EPDM	NBR	different medium
Operation	gearbox	lever	differs

Example format. The set of parameters depends on the valve type and is agreed before ordering.

Parameter alignment

Body, seat and stem materials are fixed in the specification.
Differences from the original item — length, class, actuator — are stated in writing.
Required documents and tests are included in the order scope before it is placed.

Pre-shipment checks

Nameplate checked: type, DN, PN, material, batch number.
Travel and the extreme positions of the closure member are checked.
Completeness of the actuator and fasteners is checked.
Sealing surfaces and preservation are inspected.

Documents

Supply contract and the agreed specification
Invoice and delivery documents
Product data sheet and test reports in the scope the order provides for
Conformity assessment documents where the item falls under such requirements

Risks we remove

The item falls under a different form of conformity assessment than expected: established before ordering from the customs code and parameters.
Face-to-face mismatch: removed by checking against the line drawing before ordering.
The actuator does not match the site supply: checked in the datasheet.

Who it suits

Chief mechanic and chief power engineer services
Design and installation contractors
Water treatment, heating networks, chemical processing

Stages of work

Line parameters

We collect DN, PN, medium, temperature and the connection type.

DN · PN · MEDIUM · T

Selection

We determine the type, body material, leakage class and operation.

BODY · SEAT · ACTUATOR

Documents

We establish which requirements apply to the item and what the order will include.

TR CU · ORDER SCOPE

Inspection

Nameplate, travel and completeness checked before shipment.

NAMEPLATE · TRAVEL · SCOPE

Delivery

Goods on site and the documents for acceptance.

DELIVERY NOTE · DATA SHEET

What to send for a quote

DN, PN, connection type
Medium and temperature
Datasheet or current specification

Questions and answers

The valve does not fit the face-to-face length. What now?

Face-to-face length is set by the series standard, and different series of the same DN differ. So before ordering we check it against the drawing of the section or a site measurement, together with the connection type and the position of the mating flanges. If the required series is unavailable, we show which substitution needs a spool piece re-welded and which does not.

We only need valve spares, not the valve itself.

This is a routine task: seats, seals, stems, drive units and repair kits. Selection needs the valve type and model, DN, PN and, preferably, photos of the nameplate and the disassembled unit. If the model cannot be identified we work from measurements, exactly as with equipment spares.

What should we state if there is no datasheet?

The valve type, DN and PN, medium and temperature, and the method of operation are enough. We will clarify the rest together. The point of a request is to start the conversation, not to submit a flawless specification.

Do valves require conformity assessment?

Valves operating under pressure above 0.05 MPa are assessed under TR CU 032/2013: the form of assessment depends on the category, which follows from pressure, diameter and medium. For explosive atmospheres TR CU 012/2011 applies, with mandatory certification. The specific conclusion follows from the customs code and the item parameters.

Related capabilities

Sealing solutions

Mechanical, lip, O-ring, packing and gasket solutions. Selected by medium, temperature, pressure and speed.

Learn more →02

Quality control and acceptance

Pre-shipment checks in the scope written into the order, with the result recorded.

Learn more →03

Logistics, foreign trade and documents

Route, insurance, clearance and a complete document set. One contract with a Russian legal entity.

Learn more →

Send us the task — we come back with options

A drawing, a photo of the assembly, a nameplate, a part number or a description of what has to work. We review the inputs, ask what is missing and show the available options with price, lead time and differences.

Request a valve selection Contacts